The RN 9500 is the ultimate high production, quality rotary numbering system,    loaded with features found in no
other competitive machine. This dramatically increases your numbering production    capability with greater 
versatility. 

The RN 9500 features a continuos running main shaft that permits a numbering speed up to 10,000 sheet per hour,
 regardless of the number of printheads. With a twenty four head set-up you can produce up to 240,000 
quality numbers per hour! This means greater productivity , and higher profits.
FEATURES
ADVANTAGES
Speed: Up to 20,000 sheets per hour Higher production levels, depending on job requirements
Number of Heads: Up to 42 Increase Productivity. Multiple up numbering in a single pass.
(Numbering Speed is not affected by the number of printheads.)
Oscillating Ink Roller System Superior Image quality. Economical - use the ink off your shelf or match to MPS color.
Large Split Holding Ring (18.86" cir) Full bleed 11' x 17" and (A3) - Flexible number placement
Electronic Repeat: 0-99 Adaptability - put the same number on consecutive sheets.
Print Position Adjustment Fast, easy set-up - adjust number on the run.
Simplified Controls User friendly operation - all easily accessible.
Sheet Counter Factory installed, 8 digit LCD.
Automatic Bottom-of-Pile Air Suction Feed Top loading for continuous operation, greater productivity.
Base with Three Individual Pumps Seperate pumps control the pneumatics, vacuum, and sheet separation air flow, all contained in base unit.
Lift Out Perforating, Scoring, Slitting Assembly Combine any/all operations for one pass finishing with true professional results. Large selection of blades.
Impression Adjustment Precise pressure adjustment from single sheet to multiple sets. Independent side-to-side.
110V Standard   (220V optional) 110V plug-in and run, no special wiring required.
Adjust print position on the run - quick and easy.
Shown with 8 heads, strike block and 3 holding rings. The 8 head setup is perfect for a 4-up ticket job - two numbers per ticket at a production rate of 40,000 tickets per hour. (80,000 impressions)
Optional micro perforating with 72 T.P.I. Assembly is easily mounted on our lift out delivery unit.
Base equipped with three individual pumps for control of the pneumatics, sheet vacuum, and sheet separation air flow. All neatly contained in the bottom of the unit, for easy access.
Oscillating Roller System provides full machine width and coverage. Ability to match and PMS color. Provides crisp, clean images that meet or exceed letterpress quality.
Lift out air suction feeder with adjustable paper alignment for quick registration
Strike block available in various sizes for marginal crash imprinting. Plates may be sourced in magnesium, plastic photopolymer, or rubber.
Lift out delivery system allows easy set-up change with adjustable depth control for perforating, scoring, and slitting. Large 1 1/16" diameter hard chromium plated steel shafts and 2 1/2" diameter solid blades

 

 

 

 

		
 
Specifications
Size 62"L x 32" W x 48" H (1575mm x 813mm x 1220mm)
Weight (Net) 370 lbs. (169kg)
Sheet Size Min. 4 1/2" x 5" (114mm x 127mm),
Max. 17 1/2" x 23" (445mm x 585mm)
Power Requirement 110/1 standard, other voltages optional
Speed Numbering up to 10,000 sheets per hour - perf, slit,
score only up to 20,000 sheets per hour.
Number of Heads Up to 7 straight or 5 convex per holding ring - Max. 42
Number of Holding Rings Up to 6
Minimum Spacing Between Heads on Same Holding Ring 1.82" parallel (46mm)
2.75" Convex (70mm)
Maximum Spacing Between Heads on Same Holding Ring 17" parallel (432mm)
16.1" Convex (409mm)
Minimum Spacing of Adjacent Parallel Heads 2.875" (73mm)
Minimum Spacing of Adjacent Convex Heads 2.375" (60mm)
*Specifications are subject to change without notice
*Worldwide patents pending		 MADE IN U.S.A.
Perforating Blade Specifications
#1008 1/2" cut .061 Tie 1.8 TPI 14 teeth
#1006 3/8" cut .061 Tie 2.3 TPI 18 teeth
#1004 1/4" cut .052 Tie 3.3 TPI 26 teeth
#1003 3/16" cut .043 Tie 4.3 TPI 34 teeth
#1002 1/8" cut .046 Tie 6.0 TPI 46 teeth
#1002-30 1/8" cut .032 Tie 6.5 TPI 50 teeth
#1001 1/16" cut .039 Tie 10.0 TPI 77 teeth
#1005 1/32" cut .056 Tie 11.5 TPI 90 teeth
#1007 1/32" cut .031 Tie 16.0 TPI 126 teeth
#1009 1/32" cut .021 Tie 19.0 TPI 150 teeth
MP 1072 Micro-Perf 72.0 TPI 565 teeth
TPI: Teeth Per Inch Tie: Distance Between Cuts
(Note: 1002 Blade is standard supplied with machines)
Check with us for Knock Out Perf!
7 wheel, curved base, spring return, 3/16" Gothic backward counting with sinkable zeros as standard.
A variety of alternative character styles and sizes are available upon request including detachable "No" slide prefixes.